Linux lhjmq-records 5.15.0-118-generic #128-Ubuntu SMP Fri Jul 5 09:28:59 UTC 2024 x86_64
Your IP : 3.145.179.30
# SPDX-License-Identifier: GPL-2.0-only
menuconfig RC_CORE
tristate "Remote Controller support"
depends on INPUT
help
Enable support for Remote Controllers on Linux. This is
needed in order to support several video capture adapters,
standalone IR receivers/transmitters, and RF receivers.
Enable this option if you have a video capture board even
if you don't need IR, as otherwise, you may not be able to
compile the driver for your adapter.
Say Y when you have a TV or an IR device.
if RC_CORE
source "drivers/media/rc/keymaps/Kconfig"
config LIRC
bool "LIRC user interface"
help
Enable this option to enable the Linux Infrared Remote
Control user interface (e.g. /dev/lirc*). This interface
passes raw IR to and from userspace, which is needed for
IR transmitting (aka "blasting") and for the lirc daemon.
config BPF_LIRC_MODE2
bool "Support for eBPF programs attached to lirc devices"
depends on BPF_SYSCALL
depends on RC_CORE=y
depends on LIRC
help
Allow attaching eBPF programs to a lirc device using the bpf(2)
syscall command BPF_PROG_ATTACH. This is supported for raw IR
receivers.
These eBPF programs can be used to decode IR into scancodes, for
IR protocols not supported by the kernel decoders.
menuconfig RC_DECODERS
bool "Remote controller decoders"
if RC_DECODERS
config IR_NEC_DECODER
tristate "Enable IR raw decoder for the NEC protocol"
select BITREVERSE
help
Enable this option if you have IR with NEC protocol, and
if the IR is decoded in software
config IR_RC5_DECODER
tristate "Enable IR raw decoder for the RC-5 protocol"
select BITREVERSE
help
Enable this option if you have IR with RC-5 protocol, and
if the IR is decoded in software
config IR_RC6_DECODER
tristate "Enable IR raw decoder for the RC6 protocol"
select BITREVERSE
help
Enable this option if you have an infrared remote control which
uses the RC6 protocol, and you need software decoding support.
config IR_JVC_DECODER
tristate "Enable IR raw decoder for the JVC protocol"
select BITREVERSE
help
Enable this option if you have an infrared remote control which
uses the JVC protocol, and you need software decoding support.
config IR_SONY_DECODER
tristate "Enable IR raw decoder for the Sony protocol"
select BITREVERSE
help
Enable this option if you have an infrared remote control which
uses the Sony protocol, and you need software decoding support.
config IR_SANYO_DECODER
tristate "Enable IR raw decoder for the Sanyo protocol"
select BITREVERSE
help
Enable this option if you have an infrared remote control which
uses the Sanyo protocol (Sanyo, Aiwa, Chinon remotes),
and you need software decoding support.
config IR_SHARP_DECODER
tristate "Enable IR raw decoder for the Sharp protocol"
select BITREVERSE
help
Enable this option if you have an infrared remote control which
uses the Sharp protocol (Sharp, Denon), and you need software
decoding support.
config IR_MCE_KBD_DECODER
tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol"
select BITREVERSE
help
Enable this option if you have a Microsoft Remote Keyboard for
Windows Media Center Edition, which you would like to use with
a raw IR receiver in your system.
config IR_XMP_DECODER
tristate "Enable IR raw decoder for the XMP protocol"
select BITREVERSE
help
Enable this option if you have IR with XMP protocol, and
if the IR is decoded in software
config IR_IMON_DECODER
tristate "Enable IR raw decoder for the iMON protocol"
help
Enable this option if you have iMON PAD or Antec Veris infrared
remote control and you would like to use it with a raw IR
receiver, or if you wish to use an encoder to transmit this IR.
config IR_RCMM_DECODER
tristate "Enable IR raw decoder for the RC-MM protocol"
help
Enable this option when you have IR with RC-MM protocol, and
you need the software decoder. The driver supports 12,
24 and 32 bits RC-MM variants. You can enable or disable the
different modes using the following RC protocol keywords:
'rc-mm-12', 'rc-mm-24' and 'rc-mm-32'.
To compile this driver as a module, choose M here: the module
will be called ir-rcmm-decoder.
endif #RC_DECODERS
menuconfig RC_DEVICES
bool "Remote Controller devices"
if RC_DEVICES
config RC_ATI_REMOTE
tristate "ATI / X10 based USB RF remote controls"
depends on USB
help
Say Y here if you want to use an X10 based USB remote control.
These are RF remotes with USB receivers.
Such devices include the ATI remote that comes with many of ATI's
All-In-Wonder video cards, the X10 "Lola" remote, NVIDIA RF remote,
Medion RF remote, and SnapStream FireFly remote.
This driver provides mouse pointer, left and right mouse buttons,
and maps all the other remote buttons to keypress events.
To compile this driver as a module, choose M here: the module will be
called ati_remote.
config IR_ENE
tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
depends on PNP || COMPILE_TEST
help
Say Y here to enable support for integrated infrared receiver
/transceiver made by ENE.
You can see if you have it by looking at lspnp output.
Output should include ENE0100 ENE0200 or something similar.
To compile this driver as a module, choose M here: the
module will be called ene_ir.
config IR_HIX5HD2
tristate "Hisilicon hix5hd2 IR remote control"
depends on OF || COMPILE_TEST
help
Say Y here if you want to use hisilicon hix5hd2 remote control.
To compile this driver as a module, choose M here: the module will be
called ir-hix5hd2.
If you're not sure, select N here
config IR_IMON
tristate "SoundGraph iMON Receiver and Display"
depends on USB
help
Say Y here if you want to use a SoundGraph iMON (aka Antec Veris)
IR Receiver and/or LCD/VFD/VGA display.
To compile this driver as a module, choose M here: the
module will be called imon.
config IR_IMON_RAW
tristate "SoundGraph iMON Receiver (early raw IR models)"
depends on USB
help
Say Y here if you want to use a SoundGraph iMON IR Receiver,
early raw models.
To compile this driver as a module, choose M here: the
module will be called imon_raw.
config IR_MCEUSB
tristate "Windows Media Center Ed. eHome Infrared Transceiver"
depends on USB
help
Say Y here if you want to use a Windows Media Center Edition
eHome Infrared Transceiver.
To compile this driver as a module, choose M here: the
module will be called mceusb.
config IR_ITE_CIR
tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver"
depends on PNP || COMPILE_TEST
help
Say Y here to enable support for integrated infrared receivers
/transceivers made by ITE Tech Inc. These are found in
several ASUS devices, like the ASUS Digimatrix or the ASUS
EEEBox 1501U.
To compile this driver as a module, choose M here: the
module will be called ite-cir.
config IR_FINTEK
tristate "Fintek Consumer Infrared Transceiver"
depends on PNP || COMPILE_TEST
help
Say Y here to enable support for integrated infrared receiver
/transceiver made by Fintek. This chip is found on assorted
Jetway motherboards (and of course, possibly others).
To compile this driver as a module, choose M here: the
module will be called fintek-cir.
config IR_MESON
tristate "Amlogic Meson IR remote receiver"
depends on ARCH_MESON || COMPILE_TEST
help
Say Y if you want to use the IR remote receiver available
on Amlogic Meson SoCs.
To compile this driver as a module, choose M here: the
module will be called meson-ir.
config IR_MESON_TX
tristate "Amlogic Meson IR TX"
depends on ARCH_MESON || COMPILE_TEST
help
Say Y if you want to use the IR transmitter available on
Amlogic Meson SoCs.
To compile this driver as a module, choose M here: the
module will be called meson-ir-tx.
config IR_MTK
tristate "Mediatek IR remote receiver"
depends on ARCH_MEDIATEK || COMPILE_TEST
help
Say Y if you want to use the IR remote receiver available
on Mediatek SoCs.
To compile this driver as a module, choose M here: the
module will be called mtk-cir.
config IR_NUVOTON
tristate "Nuvoton w836x7hg Consumer Infrared Transceiver"
depends on PNP || COMPILE_TEST
help
Say Y here to enable support for integrated infrared receiver
/transceiver made by Nuvoton (formerly Winbond). This chip is
found in the ASRock ION 330HT, as well as assorted Intel
DP55-series motherboards (and of course, possibly others).
To compile this driver as a module, choose M here: the
module will be called nuvoton-cir.
config IR_REDRAT3
tristate "RedRat3 IR Transceiver"
depends on USB
select NEW_LEDS
select LEDS_CLASS
help
Say Y here if you want to use a RedRat3 Infrared Transceiver.
To compile this driver as a module, choose M here: the
module will be called redrat3.
config IR_SPI
tristate "SPI connected IR LED"
depends on SPI && LIRC
depends on OF || COMPILE_TEST
help
Say Y if you want to use an IR LED connected through SPI bus.
To compile this driver as a module, choose M here: the module will be
called ir-spi.
config IR_STREAMZAP
tristate "Streamzap PC Remote IR Receiver"
depends on USB
help
Say Y here if you want to use a Streamzap PC Remote
Infrared Receiver.
To compile this driver as a module, choose M here: the
module will be called streamzap.
config IR_WINBOND_CIR
tristate "Winbond IR remote control"
depends on (X86 && PNP) || COMPILE_TEST
select NEW_LEDS
select LEDS_CLASS
select BITREVERSE
help
Say Y here if you want to use the IR remote functionality found
in some Winbond SuperI/O chips. Currently only the WPCD376I
chip is supported (included in some Intel Media series
motherboards).
To compile this driver as a module, choose M here: the module will
be called winbond_cir.
config IR_IGORPLUGUSB
tristate "IgorPlug-USB IR Receiver"
depends on USB
help
Say Y here if you want to use the IgorPlug-USB IR Receiver by
Igor Cesko. This device is included on the Fit-PC2.
Note that this device can only record bursts of 36 IR pulses and
spaces, which is not enough for the NEC, Sanyo and RC-6 protocol.
To compile this driver as a module, choose M here: the module will
be called igorplugusb.
config IR_IGUANA
tristate "IguanaWorks USB IR Transceiver"
depends on USB
help
Say Y here if you want to use the IguanaWorks USB IR Transceiver.
Both infrared receive and send are supported. If you want to
change the ID or the pin config, use the user space driver from
IguanaWorks.
Only firmware 0x0205 and later is supported.
To compile this driver as a module, choose M here: the module will
be called iguanair.
config IR_TTUSBIR
tristate "TechnoTrend USB IR Receiver"
depends on USB
select NEW_LEDS
select LEDS_CLASS
help
Say Y here if you want to use the TechnoTrend USB IR Receiver. The
driver can control the led.
To compile this driver as a module, choose M here: the module will
be called ttusbir.
config IR_RX51
tristate "Nokia N900 IR transmitter diode"
depends on (OMAP_DM_TIMER && PWM_OMAP_DMTIMER && ARCH_OMAP2PLUS || COMPILE_TEST) && RC_CORE
help
Say Y or M here if you want to enable support for the IR
transmitter diode built in the Nokia N900 (RX51) device.
The driver uses omap DM timers for generating the carrier
wave and pulses.
source "drivers/media/rc/img-ir/Kconfig"
config RC_LOOPBACK
tristate "Remote Control Loopback Driver"
help
Say Y here if you want support for the remote control loopback
driver which allows TX data to be sent back as RX data.
This is mostly useful for debugging purposes.
If you're not sure, select N here.
To compile this driver as a module, choose M here: the module will
be called rc_loopback.
config IR_GPIO_CIR
tristate "GPIO IR remote control"
depends on (OF && GPIOLIB) || COMPILE_TEST
help
Say Y if you want to use GPIO based IR Receiver.
To compile this driver as a module, choose M here: the module will
be called gpio-ir-recv.
config IR_GPIO_TX
tristate "GPIO IR Bit Banging Transmitter"
depends on LIRC
depends on (OF && GPIOLIB) || COMPILE_TEST
help
Say Y if you want to a GPIO based IR transmitter. This is a
bit banging driver.
To compile this driver as a module, choose M here: the module will
be called gpio-ir-tx.
config IR_PWM_TX
tristate "PWM IR transmitter"
depends on LIRC
depends on PWM
depends on OF || COMPILE_TEST
help
Say Y if you want to use a PWM based IR transmitter. This is
more power efficient than the bit banging gpio driver.
To compile this driver as a module, choose M here: the module will
be called pwm-ir-tx.
config RC_ST
tristate "ST remote control receiver"
depends on ARCH_STI || COMPILE_TEST
help
Say Y here if you want support for ST remote control driver
which allows both IR and UHF RX.
The driver passes raw pulse and space information to the LIRC decoder.
If you're not sure, select N here.
config IR_SUNXI
tristate "SUNXI IR remote control"
depends on ARCH_SUNXI || COMPILE_TEST
help
Say Y if you want to use sunXi internal IR Controller
To compile this driver as a module, choose M here: the module will
be called sunxi-ir.
config IR_SERIAL
tristate "Homebrew Serial Port Receiver"
help
Say Y if you want to use Homebrew Serial Port Receivers and
Transceivers.
To compile this driver as a module, choose M here: the module will
be called serial-ir.
config IR_SERIAL_TRANSMITTER
bool "Serial Port Transmitter"
depends on IR_SERIAL
help
Serial Port Transmitter support
config IR_SIR
tristate "Built-in SIR IrDA port"
help
Say Y if you want to use a IrDA SIR port Transceivers.
To compile this driver as a module, choose M here: the module will
be called sir-ir.
config RC_XBOX_DVD
tristate "Xbox DVD Movie Playback Kit"
depends on USB
help
Say Y here if you want to use the Xbox DVD Movie Playback Kit.
These are IR remotes with USB receivers for the Original Xbox (2001).
To compile this driver as a module, choose M here: the module will be
called xbox_remote.
config IR_TOY
tristate "Infrared Toy and IR Droid"
depends on USB
help
Say Y here if you want to use the Infrared Toy or IR Droid, USB
versions.
To compile this driver as a module, choose M here: the module will be
called ir_toy.
endif #RC_DEVICES
endif #RC_CORE
|