Linux lhjmq-records 5.15.0-118-generic #128-Ubuntu SMP Fri Jul 5 09:28:59 UTC 2024 x86_64
Your IP : 3.139.239.25
# SPDX-License-Identifier: GPL-2.0-only
#
# Phy drivers for Broadcom platforms
#
config PHY_BCM63XX_USBH
tristate "BCM63xx USBH PHY driver"
depends on BMIPS_GENERIC || COMPILE_TEST
select GENERIC_PHY
help
Enable this to support the BCM63xx USBH PHY driver.
If unsure, say N.
config PHY_CYGNUS_PCIE
tristate "Broadcom Cygnus PCIe PHY driver"
depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST)
select GENERIC_PHY
default ARCH_BCM_CYGNUS
help
Enable this to support the Broadcom Cygnus PCIe PHY.
If unsure, say N.
config PHY_BCM_SR_USB
tristate "Broadcom Stingray USB PHY driver"
depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
select GENERIC_PHY
default ARCH_BCM_IPROC
help
Enable this to support the Broadcom Stingray USB PHY
driver. It supports all versions of Superspeed and
Highspeed PHYs.
If unsure, say N.
config BCM_KONA_USB2_PHY
tristate "Broadcom Kona USB2 PHY Driver"
depends on HAS_IOMEM
select GENERIC_PHY
help
Enable this to support the Broadcom Kona USB 2.0 PHY.
config PHY_BCM_NS_USB2
tristate "Broadcom Northstar USB 2.0 PHY Driver"
depends on ARCH_BCM_IPROC || COMPILE_TEST
depends on HAS_IOMEM && OF
select GENERIC_PHY
help
Enable this to support Broadcom USB 2.0 PHY connected to the USB
controller on Northstar family.
config PHY_BCM_NS_USB3
tristate "Broadcom Northstar USB 3.0 PHY Driver"
depends on ARCH_BCM_IPROC || COMPILE_TEST
depends on HAS_IOMEM && OF
depends on MDIO_BUS
select GENERIC_PHY
help
Enable this to support Broadcom USB 3.0 PHY connected to the USB
controller on Northstar family.
config PHY_NS2_PCIE
tristate "Broadcom Northstar2 PCIe PHY driver"
depends on (OF && MDIO_BUS_MUX_BCM_IPROC) || (COMPILE_TEST && MDIO_BUS)
select GENERIC_PHY
default ARCH_BCM_IPROC
help
Enable this to support the Broadcom Northstar2 PCIe PHY.
If unsure, say N.
config PHY_NS2_USB_DRD
tristate "Broadcom Northstar2 USB DRD PHY support"
depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
select GENERIC_PHY
select EXTCON
default ARCH_BCM_IPROC
help
Enable this to support the Broadcom Northstar2 USB DRD PHY.
This driver initializes the PHY in either HOST or DEVICE mode.
The host or device configuration is read from device tree.
If unsure, say N.
config PHY_BRCM_SATA
tristate "Broadcom SATA PHY driver"
depends on ARCH_BRCMSTB || ARCH_BCM_IPROC || BMIPS_GENERIC || \
ARCH_BCM_63XX || COMPILE_TEST
depends on OF
select GENERIC_PHY
default ARCH_BCM_IPROC
help
Enable this to support the Broadcom SATA PHY.
If unsure, say N.
config PHY_BRCM_USB
tristate "Broadcom STB USB PHY driver"
depends on ARCH_BCM4908 || ARCH_BRCMSTB || COMPILE_TEST
depends on OF
select GENERIC_PHY
select SOC_BRCMSTB if ARCH_BRCMSTB
default ARCH_BCM4908 || ARCH_BRCMSTB
help
Enable this to support the Broadcom STB USB PHY.
This driver is required by the USB XHCI, EHCI and OHCI
drivers.
If unsure, say N.
config PHY_BCM_SR_PCIE
tristate "Broadcom Stingray PCIe PHY driver"
depends on OF && (ARCH_BCM_IPROC || COMPILE_TEST)
select GENERIC_PHY
select MFD_SYSCON
default ARCH_BCM_IPROC
help
Enable this to support the Broadcom Stingray PCIe PHY
If unsure, say N.
|