Linux lhjmq-records 5.15.0-118-generic #128-Ubuntu SMP Fri Jul 5 09:28:59 UTC 2024 x86_64
Your IP : 3.137.221.114
#!/bin/sh
# This script is meant as an example of using the sg_persist utility
# in the sg3_utils package. This script works as expected on the
# author's Fujitsu MAM3184, Seagate ST373455 and ST9146803SS disks.
#
# Version 2.0 20171104
# N.B. make sure the device name is correct for your environment.
key="123abc"
key2="333aaa"
kk=${key}
rtype="1"
verbose=""
usage()
{
echo "Usage: sg_persist_tst.sh [-e] [-h] [-s] [-v] <device>"
echo " where:"
echo " -e, --exclusive exclusive access (def: write " \
"exclusive)"
echo " -h, --help print usage message"
echo " -s, --second use second key"
echo " -v, --verbose more verbose output"
echo " -vv even more verbose output"
echo " -vvv even more verbose output"
echo ""
echo "Test SCSI Persistent Reservations with sg_persist utility."
echo "Default key is ${key} and alternate, second key is ${key2} ."
echo "Should be harmless (unless one of those keys is already in use)."
echo "The APTPL bit is not set in the PR register so a power cycle"
echo "on the device will clear the reservation if this script stops"
echo "(or is stopped) before clearing it. Tape drives only seem to "
echo "support 'exclusive access' type (so use '-e')."
}
opt="$1"
while test ! -z "$opt" -a -z "${opt##-*}"; do
opt=${opt#-}
case "$opt" in
e|-exclusive) rtype="3" ;;
h|-help) usage ; exit 0 ;;
s|-second) kk=${key2} ;;
vvv) verbose="-vvv" ;;
vv) verbose="-vv" ;;
v|-verbose) verbose="-v" ;;
*) echo "Unknown option: -$opt " ; exit 1 ;;
esac
shift
opt="$1"
done
if [ $# -lt 1 ]
then
usage
exit 1
fi
echo ">>> try to report capabilities:"
sg_persist -c ${verbose} "$1"
res=$?
case "$res" in
0) ;;
1) echo " syntax error" ;;
2) echo " not ready" ;;
3) echo " medium error" ;;
5) echo " illegal request, report capabilities not supported?" ;;
6) echo " unit attention" ;;
9) echo " illegal request, Persistent Reserve (In) not supported" ;;
11) echo " aborted command" ;;
15) echo " file error with $1 " ;;
20) echo " no sense" ;;
21) echo " recovered error" ;;
33) echo " timeout" ;;
97) echo " response fails sanity" ;;
98) echo " other SCSI error" ;;
99) echo " other error" ;;
*) echo " unknown exit status for sg_persist: $res" ;;
esac
echo ""
sleep 1
echo ">>> check if any keys are registered:"
sg_persist --no-inquiry --read-keys ${verbose} "$1"
sleep 1
echo
echo ">>> register a key:"
sg_persist -n --out --register --param-sark=${kk} ${verbose} "$1"
sleep 1
echo
echo ">>> now key ${kk} should be registered:"
sg_persist -n --read-keys ${verbose} "$1"
sleep 1
echo
echo ">>> reserve the device (based on key ${kk}):"
sg_persist -n --out --reserve --param-rk=${kk} --prout-type=${rtype} ${verbose} "$1"
sleep 1
echo
echo ">>> check if the device is reserved (it should be now):"
sg_persist -n --read-reservation ${verbose} "$1"
sleep 1
echo
echo ">>> try to 'read full status' (may not be supported):"
sg_persist -n --read-full-status ${verbose} "$1"
sleep 1
echo
echo ">>> now release reservation:"
sg_persist -n --out --release --param-rk=${kk} --prout-type=${rtype} ${verbose} "$1"
sleep 1
echo
echo ">>> check if the device is reserved (it should _not_ be now):"
sg_persist -n --read-reservation ${verbose} "$1"
sleep 1
echo
echo ">>> unregister key ${kk}:"
sg_persist -n --out --register --param-rk=${kk} ${verbose} "$1"
sleep 1
echo
echo ">>> now key ${kk} should not be registered:"
sg_persist -n -k ${verbose} "$1"
sleep 1
|