Linux lhjmq-records 5.15.0-118-generic #128-Ubuntu SMP Fri Jul 5 09:28:59 UTC 2024 x86_64
Your IP : 18.189.182.15
/* SPDX-License-Identifier: GPL-2.0-only */
/* Copyright (c) 2020 Pengutronix, Marc Kleine-Budde <kernel@pengutronix.de>
* Copyright (c) 2021 Vincent Mailhol <mailhol.vincent@wanadoo.fr>
*/
#ifndef _CAN_BITTIMING_H
#define _CAN_BITTIMING_H
#include <linux/netdevice.h>
#include <linux/can/netlink.h>
#define CAN_SYNC_SEG 1
/* Kilobits and Megabits per second */
#define CAN_KBPS 1000UL
#define CAN_MBPS 1000000UL
/* Megahertz */
#define CAN_MHZ 1000000UL
/*
* struct can_tdc - CAN FD Transmission Delay Compensation parameters
*
* At high bit rates, the propagation delay from the TX pin to the RX
* pin of the transceiver causes measurement errors: the sample point
* on the RX pin might occur on the previous bit.
*
* To solve this issue, ISO 11898-1 introduces in section 11.3.3
* "Transmitter delay compensation" a SSP (Secondary Sample Point)
* equal to the distance, in time quanta, from the start of the bit
* time on the TX pin to the actual measurement on the RX pin.
*
* This structure contains the parameters to calculate that SSP.
*
* @tdcv: Transmitter Delay Compensation Value. Distance, in time
* quanta, from when the bit is sent on the TX pin to when it is
* received on the RX pin of the transmitter. Possible options:
*
* 0: automatic mode. The controller dynamically measures @tdcv
* for each transmitted CAN FD frame.
*
* Other values: manual mode. Use the fixed provided value.
*
* @tdco: Transmitter Delay Compensation Offset. Offset value, in time
* quanta, defining the distance between the start of the bit
* reception on the RX pin of the transceiver and the SSP
* position such that SSP = @tdcv + @tdco.
*
* If @tdco is zero, then TDC is disabled and both @tdcv and
* @tdcf should be ignored.
*
* @tdcf: Transmitter Delay Compensation Filter window. Defines the
* minimum value for the SSP position in time quanta. If SSP is
* less than @tdcf, then no delay compensations occur and the
* normal sampling point is used instead. The feature is enabled
* if and only if @tdcv is set to zero (automatic mode) and @tdcf
* is configured to a value greater than @tdco.
*/
struct can_tdc {
u32 tdcv;
u32 tdco;
u32 tdcf;
};
/*
* struct can_tdc_const - CAN hardware-dependent constant for
* Transmission Delay Compensation
*
* @tdcv_max: Transmitter Delay Compensation Value maximum value.
* Should be set to zero if the controller does not support
* manual mode for tdcv.
* @tdco_max: Transmitter Delay Compensation Offset maximum value.
* Should not be zero. If the controller does not support TDC,
* then the pointer to this structure should be NULL.
* @tdcf_max: Transmitter Delay Compensation Filter window maximum
* value. Should be set to zero if the controller does not
* support this feature.
*/
struct can_tdc_const {
u32 tdcv_max;
u32 tdco_max;
u32 tdcf_max;
};
#ifdef CONFIG_CAN_CALC_BITTIMING
int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt,
const struct can_bittiming_const *btc);
void can_calc_tdco(struct net_device *dev);
#else /* !CONFIG_CAN_CALC_BITTIMING */
static inline int
can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt,
const struct can_bittiming_const *btc)
{
netdev_err(dev, "bit-timing calculation not available\n");
return -EINVAL;
}
static inline void can_calc_tdco(struct net_device *dev)
{
}
#endif /* CONFIG_CAN_CALC_BITTIMING */
int can_get_bittiming(struct net_device *dev, struct can_bittiming *bt,
const struct can_bittiming_const *btc,
const u32 *bitrate_const,
const unsigned int bitrate_const_cnt);
/*
* can_bit_time() - Duration of one bit
*
* Please refer to ISO 11898-1:2015, section 11.3.1.1 "Bit time" for
* additional information.
*
* Return: the number of time quanta in one bit.
*/
static inline unsigned int can_bit_time(const struct can_bittiming *bt)
{
return CAN_SYNC_SEG + bt->prop_seg + bt->phase_seg1 + bt->phase_seg2;
}
#endif /* !_CAN_BITTIMING_H */
|