Linux lhjmq-records 5.15.0-118-generic #128-Ubuntu SMP Fri Jul 5 09:28:59 UTC 2024 x86_64
Your IP : 13.59.83.202
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* include/linux/mmc/sd.h
*
* Copyright (C) 2005-2007 Pierre Ossman, All Rights Reserved.
*/
#ifndef LINUX_MMC_SD_H
#define LINUX_MMC_SD_H
/* SD commands type argument response */
/* class 0 */
/* This is basically the same command as for MMC with some quirks. */
#define SD_SEND_RELATIVE_ADDR 3 /* bcr R6 */
#define SD_SEND_IF_COND 8 /* bcr [11:0] See below R7 */
#define SD_SWITCH_VOLTAGE 11 /* ac R1 */
/* class 10 */
#define SD_SWITCH 6 /* adtc [31:0] See below R1 */
/* class 5 */
#define SD_ERASE_WR_BLK_START 32 /* ac [31:0] data addr R1 */
#define SD_ERASE_WR_BLK_END 33 /* ac [31:0] data addr R1 */
/* Application commands */
#define SD_APP_SET_BUS_WIDTH 6 /* ac [1:0] bus width R1 */
#define SD_APP_SD_STATUS 13 /* adtc R1 */
#define SD_APP_SEND_NUM_WR_BLKS 22 /* adtc R1 */
#define SD_APP_OP_COND 41 /* bcr [31:0] OCR R3 */
#define SD_APP_SEND_SCR 51 /* adtc R1 */
/* class 11 */
#define SD_READ_EXTR_SINGLE 48 /* adtc [31:0] R1 */
#define SD_WRITE_EXTR_SINGLE 49 /* adtc [31:0] R1 */
/* OCR bit definitions */
#define SD_OCR_S18R (1 << 24) /* 1.8V switching request */
#define SD_ROCR_S18A SD_OCR_S18R /* 1.8V switching accepted by card */
#define SD_OCR_XPC (1 << 28) /* SDXC power control */
#define SD_OCR_CCS (1 << 30) /* Card Capacity Status */
/*
* SD_SWITCH argument format:
*
* [31] Check (0) or switch (1)
* [30:24] Reserved (0)
* [23:20] Function group 6
* [19:16] Function group 5
* [15:12] Function group 4
* [11:8] Function group 3
* [7:4] Function group 2
* [3:0] Function group 1
*/
/*
* SD_SEND_IF_COND argument format:
*
* [31:12] Reserved (0)
* [11:8] Host Voltage Supply Flags
* [7:0] Check Pattern (0xAA)
*/
/*
* SCR field definitions
*/
#define SCR_SPEC_VER_0 0 /* Implements system specification 1.0 - 1.01 */
#define SCR_SPEC_VER_1 1 /* Implements system specification 1.10 */
#define SCR_SPEC_VER_2 2 /* Implements system specification 2.00-3.0X */
/*
* SD bus widths
*/
#define SD_BUS_WIDTH_1 0
#define SD_BUS_WIDTH_4 2
/*
* SD_SWITCH mode
*/
#define SD_SWITCH_CHECK 0
#define SD_SWITCH_SET 1
/*
* SD_SWITCH function groups
*/
#define SD_SWITCH_GRP_ACCESS 0
/*
* SD_SWITCH access modes
*/
#define SD_SWITCH_ACCESS_DEF 0
#define SD_SWITCH_ACCESS_HS 1
/*
* Erase/discard
*/
#define SD_ERASE_ARG 0x00000000
#define SD_DISCARD_ARG 0x00000001
#endif /* LINUX_MMC_SD_H */
|